build-steps:dc_to_dc_wire
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| build-steps:dc_to_dc_wire [2025/08/11 23:15] – admin | build-steps:dc_to_dc_wire [2026/04/08 20:30] (current) – admin | ||
|---|---|---|---|
| Line 12: | Line 12: | ||
| [[Tools: | [[Tools: | ||
| [[Tools: | [[Tools: | ||
| - | [[Tools:Dab Torch]]\\ | + | [[Tools:1/4 Ratchet]]\\ |
| + | [[Tools:8mm Socket]]\\ | ||
| [[Tools: | [[Tools: | ||
| [[Tools: | [[Tools: | ||
| ===Hardware Required=== | ===Hardware Required=== | ||
| - | [[Hardware: | ||
| ===Equipment Required=== | ===Equipment Required=== | ||
| + | [[Equipment: | ||
| ===Bulk Items Required=== | ===Bulk Items Required=== | ||
| Line 32: | Line 32: | ||
| ===Quick Reference=== | ===Quick Reference=== | ||
| - | Here is where to put details that you will likely need to look back at even once you've done this step many times before like measurements or gotchas that you've experienced | ||
| - | |||
| - | Here's an example of an embeded photo that is a thumbnail that can be clicked on to get a closer look. | ||
| - | |||
| - | {{build-steps: | ||
| Line 61: | Line 56: | ||
| * Use a quarter to turn clips 90 degres and remove cover | * Use a quarter to turn clips 90 degres and remove cover | ||
| * Pop battery cover off by pressing in 2 clips and pulling up. Slide to the side | * Pop battery cover off by pressing in 2 clips and pulling up. Slide to the side | ||
| + | | ||
| * Pull 8mm nut from 70amp fuse that goes to 6awg wire that runs over to the foot well. This is the wire to the upfit harness that isn’t used with our install. | * Pull 8mm nut from 70amp fuse that goes to 6awg wire that runs over to the foot well. This is the wire to the upfit harness that isn’t used with our install. | ||
| - | | + | |
| + | | ||
| + | | ||
| * Trim back of wire tray so 6awg wire can run directly back behind the seat. | * Trim back of wire tray so 6awg wire can run directly back behind the seat. | ||
| + | | ||
| * Route wire from spool in cargo area up through the path that was opened by removing the upfit harness | * Route wire from spool in cargo area up through the path that was opened by removing the upfit harness | ||
| + | | ||
| * Crimp (#10) small end 6awg lug onto new wire after stripping it with big stripper. While holding wire with crimper bend end over 90 degrees like wire end that you removed. | * Crimp (#10) small end 6awg lug onto new wire after stripping it with big stripper. While holding wire with crimper bend end over 90 degrees like wire end that you removed. | ||
| + | | ||
| * Route wire down with a loop and back up through where the old wire was removed. | * Route wire down with a loop and back up through where the old wire was removed. | ||
| + | | ||
| * Pop battery cover back on and make sure 2 clips engage. | * Pop battery cover back on and make sure 2 clips engage. | ||
| * Put battery floor cover back on after making sure it is vaccumed all around the area and twaist claps 90 degrees with a quarter to hold it in place. | * Put battery floor cover back on after making sure it is vaccumed all around the area and twaist claps 90 degrees with a quarter to hold it in place. | ||
| Line 74: | Line 76: | ||
| * Re-install A-Pillar lower cover by popping in top clip and re-installing 5 philips screws | * Re-install A-Pillar lower cover by popping in top clip and re-installing 5 philips screws | ||
| * Cut wire at C-pillar (see photo). Wire is live so wrap with electrical tap. Then wrap and put under driver seat | * Cut wire at C-pillar (see photo). Wire is live so wrap with electrical tap. Then wrap and put under driver seat | ||
| + | | ||
| + | |||
| + | ===Stuff we've already tried=== | ||
| + | * We tried using crimps that already had a 90 degree bend and they cost way more and were a little harder to crimp. Using the straight ones and just bending them is only the smallest amount more effort for significantly less money. | ||
| + | |||
| + | ===Stuff to do=== | ||
| + | * Make sticker to go on old upfit harness wire - | ||
| + | * Length of 6awg wire | ||
| + | * Sticker for DC-DC wire | ||
| - | To-do - Test 90 degree lugs - | ||
| - | Make sticker to go on old upfit harness wire - | ||
| - | Length of 6awg wire | ||
| - | Sticker for DC-DC wire | ||
| - | This is a step by step list to do the step along with embeded photos and videos as necessary. | ||
/home/mediumgg/public_html/data/attic/build-steps/dc_to_dc_wire.1754954140.txt.gz · Last modified: by admin