Differences

This shows you the differences between two versions of the page.

--- start [2025/08/09 01:59] – created admin
+++ start [2025/08/11 17:48] (current) – admin
@@ Line 1: / Line 1: @@
-Cross Van wiring
+====Page templates:====
+[[Tools:Tools Template]]\\
+[[Equipment:Equipment Template]]\\
+[[Hardware:Hardware Template]]\\
+[[Supplies:Supplies Template]]\\
+[[Instructions:Instructions Template]]\\
+[[Build-Steps:Install fresh water lines in 2 water tanks]] \\
+====Build Instructions====
+===Done before van arrives===
+[[Build-Steps:Power Plate Assembly]]\\
+[[Build-Steps:Fridge Cabinet Assembly]]\\
+[[Build-Steps:Prep Countertops]]\\
+[[Build-Steps:Assembly Bed Base]]\\
+[[Build-Steps:Cabinet Assembly]]\\
+[[Build-Steps:Wire Cabinet]]\\
+[[Build-Steps:Plumbing cabinet]] \\
+[[Build-Steps:Prep and Varnish Panels]]\\
+[[Build-Steps:Prep Bed Tops]]\\
+===Day 1===
+[[Build-Steps:Fuel line to tank]] \\
+[[Build-Steps:DC to DC wire]] \\
+[[Build-Steps:AC Vents]] \\
+[[Build-Steps:Toilet Vent]] \\
+[[Build-Steps:Shore Power plug]] \\
+[[Build-Steps:Cross Van Wires]] \\
+[[Build-Steps:Roof vent install]]\\
+[[Build-Steps:Roof Wire Box]]\\
+[[Build-Steps:Heater Install Under Van]]\\
+[[Build-Steps:Roof grid]]\\
+[[Build-Steps:Driver Wall Grid]]\\
+===Day 2===
+[[Build-Steps:Heater Install Inside Van]]\\
+[[Build-Steps:Driver side wall]]\\
+[[Build-Steps:AC Vent Install]]\\
+[[Build-Steps:Install and Insulate Floor]]\\
+[[Build-Steps:Power Plate Install]]\\
+[[Build-Steps:Power Plate Cover]]\\
+[[Build-Steps:Power Panel Install]]\\
+[[Build-Steps:Bed Back Install]]\\
+[[Build-Steps:Bed Back Block Magnet Install]]\\
+[[Build-Steps:Bed Top Install]]\\
+[[Build-Steps:Rear Door Assembly]]\\
+[[Build-Steps:Box Above Rear Doors]]\\
+[[Build-Steps:Strechy Cords for Cubbies]]\\
+[[Build-Steps:Build Heater Step]]\\
+[[Build-Steps:Configure Victron Components]]\\
+[[Build-Steps:Install Fridge Cabinet]]\\
+[[Build-Steps:Install faucet]] \\
+[[Build-Steps:Make and install undersink door]] \\
+[[Build-Steps:Run drain lines and install lower AC duct]] \\
+[[Build-Steps:Install hold down strap for AC]] \\
+[[Build-Steps:Make and install aluminum parts. FloorEdge waterbottle ]] \\[[Build-Steps:ledge, toilet glide strip]] \\
+[[Build-Steps:Make and install bed back magnet]] \\
+[[Build-Steps:Install front roller wheel and bracket]] \\
+[[Build-Steps:Insulate and install top for heater step]] \\
+[[Build-Steps:Install bed pull straps]] \\
+[[Build-Steps:Install toilet and toilet drawer]] \\
+[[Build-Steps:Wire toilet and fridge]] \\
+[[Build-Steps:Install panel above sink]] \\
+[[Build-Steps:Install TV bracket and mount]] \\
+[[Build-Steps:Install drawers and drawer slide blocks]] \\
+[[Build-Steps:Install slider door panel]] \\
+[[Build-Steps:Install stretchy cords in cubbies]] \\
+[[Build-Steps:Install above slider door parts]] \\
+[[Build-Steps:Put bottom cover on box over rear doors after insulating it]] \\
+[[Build-Steps:Put corner rubber on boxes above both doors]] \\
+[[Build-Steps:Install solar panels]] \\
+[[Build-Steps:Install Lemans fan]] \\
+[[Build-Steps:Seat belt bolt and cover install]] \\
+[[Build-Steps:Finalize puck lights]] \\
+[[Build-Steps:Test plumbing]] \\
+[[Build-Steps:Test heater]] \\
+[[Build-Steps:Configure Victron]] \\
+[[Build-Steps:Water bottle straps]] \\
 [[Auto-stripper]]