Medium Van Build Instructions

User Tools

Site Tools

Trace:
start

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
start [2025/08/09 21:22] – adminstart [2025/08/11 17:48] (current) – admin
Line 1: Line 1:
 +====Page templates:====
  
-[[Build-Steps:Fuel line to tank]] +[[Tools:Tools Template]]\\ 
-[[Build-Steps:DC to DC wire]] +[[Equipment:Equipment Template]]\\ 
-[[Build-Steps:AC Vents]] +[[Hardware:Hardware Template]]\\ 
-[[Build-Steps:Toilet Vent]] +[[Supplies:Supplies Template]]\\ 
-[[Build-Steps:Shore Power plug]] +[[Instructions:Instructions Template]]\\ 
-[[Build-Steps:Cross Van Wires]] +[[Build-Steps:Install fresh water lines in 2 water tanks]] \\
-[[Build-Steps:Plumbing cabinet]] +
-[[Build-Steps:Install faucet]] +
-[[Build-Steps:Make and install undersink door]] +
-[[Build-Steps:Run drain lines and install lower AC duct]] +
-[[Build-Steps:Install hold down strap for AC]] +
-[[Build-Steps:Install fresh water lines in 2 water tanks]] +
-[[Build-Steps:Make and install aluminum parts. FloorEdge waterbottle ]][[Build-Steps:ledge, toilet glide strip]] +
-[[Build-Steps:Make and install bed back magnet]] +
-[[Build-Steps:Install front roller wheel and bracket]] +
-[[Build-Steps:Insulate and install top for heater step]] +
-[[Build-Steps:Install bed pull straps]] +
-[[Build-Steps:Install toilet and toilet drawer]] +
-[[Build-Steps:Wire toilet and fridge]] +
-[[Build-Steps:Install panel above sink]] +
-[[Build-Steps:Install TV bracket and mount]] +
-[[Build-Steps:Install drawers and drawer slide blocks]] +
-[[Build-Steps:Install slider door panel]] +
-[[Build-Steps:Install stretchy cords in cubbies]] +
-[[Build-Steps:Install above slider door parts]] +
-[[Build-Steps:Put bottom cover on box over rear doors after insulating it]] +
-[[Build-Steps:Put corner rubber on boxes above both doors]] +
-[[Build-Steps:Install solar panels]] +
-[[Build-Steps:Install Lemans fan]] +
-[[Build-Steps:Seat belt bolt and cover install]] +
-[[Build-Steps:Finalize puck lights]] +
-[[Build-Steps:Test plumbing]] +
-[[Build-Steps:Test heater]] +
-[[Build-Steps:Configure Victron]] +
-[[Build-Steps:Water bottle straps]]+
  
 +====Build Instructions====
 +
 +===Done before van arrives===
 +
 +[[Build-Steps:Power Plate Assembly]]\\
 +[[Build-Steps:Fridge Cabinet Assembly]]\\
 +[[Build-Steps:Prep Countertops]]\\
 +[[Build-Steps:Assembly Bed Base]]\\
 +[[Build-Steps:Cabinet Assembly]]\\
 +[[Build-Steps:Wire Cabinet]]\\
 +[[Build-Steps:Plumbing cabinet]] \\
 +[[Build-Steps:Prep and Varnish Panels]]\\
 +[[Build-Steps:Prep Bed Tops]]\\
 +
 +===Day 1===
 +
 +[[Build-Steps:Fuel line to tank]] \\
 +[[Build-Steps:DC to DC wire]] \\
 +[[Build-Steps:AC Vents]] \\
 +[[Build-Steps:Toilet Vent]] \\
 +[[Build-Steps:Shore Power plug]] \\
 +[[Build-Steps:Cross Van Wires]] \\
 +[[Build-Steps:Roof vent install]]\\
 +[[Build-Steps:Roof Wire Box]]\\
 +[[Build-Steps:Heater Install Under Van]]\\
 +[[Build-Steps:Roof grid]]\\
 +[[Build-Steps:Driver Wall Grid]]\\
 +
 +===Day 2===
 +
 +[[Build-Steps:Heater Install Inside Van]]\\
 +[[Build-Steps:Driver side wall]]\\
 +[[Build-Steps:AC Vent Install]]\\
 +[[Build-Steps:Install and Insulate Floor]]\\
 +[[Build-Steps:Power Plate Install]]\\
 +[[Build-Steps:Power Plate Cover]]\\
 +
 +[[Build-Steps:Power Panel Install]]\\
 +[[Build-Steps:Bed Back Install]]\\
 +[[Build-Steps:Bed Back Block Magnet Install]]\\
 +[[Build-Steps:Bed Top Install]]\\
 +
 +[[Build-Steps:Rear Door Assembly]]\\
 +[[Build-Steps:Box Above Rear Doors]]\\
 +[[Build-Steps:Strechy Cords for Cubbies]]\\
 +[[Build-Steps:Build Heater Step]]\\
 +
 +[[Build-Steps:Configure Victron Components]]\\
 +
 +[[Build-Steps:Install Fridge Cabinet]]\\
 +[[Build-Steps:Install faucet]] \\
 +[[Build-Steps:Make and install undersink door]] \\
 +[[Build-Steps:Run drain lines and install lower AC duct]] \\
 +[[Build-Steps:Install hold down strap for AC]] \\
 +[[Build-Steps:Make and install aluminum parts. FloorEdge waterbottle ]] \\[[Build-Steps:ledge, toilet glide strip]] \\
 +[[Build-Steps:Make and install bed back magnet]] \\
 +[[Build-Steps:Install front roller wheel and bracket]] \\
 +[[Build-Steps:Insulate and install top for heater step]] \\
 +[[Build-Steps:Install bed pull straps]] \\
 +[[Build-Steps:Install toilet and toilet drawer]] \\
 +[[Build-Steps:Wire toilet and fridge]] \\
 +[[Build-Steps:Install panel above sink]] \\
 +[[Build-Steps:Install TV bracket and mount]] \\
 +[[Build-Steps:Install drawers and drawer slide blocks]] \\
 +[[Build-Steps:Install slider door panel]] \\
 +[[Build-Steps:Install stretchy cords in cubbies]] \\
 +[[Build-Steps:Install above slider door parts]] \\
 +[[Build-Steps:Put bottom cover on box over rear doors after insulating it]] \\
 +[[Build-Steps:Put corner rubber on boxes above both doors]] \\
 +[[Build-Steps:Install solar panels]] \\
 +[[Build-Steps:Install Lemans fan]] \\
 +[[Build-Steps:Seat belt bolt and cover install]] \\
 +[[Build-Steps:Finalize puck lights]] \\
 +[[Build-Steps:Test plumbing]] \\
 +[[Build-Steps:Test heater]] \\
 +[[Build-Steps:Configure Victron]] \\
 +[[Build-Steps:Water bottle straps]] \\
  
  
 [[Auto-stripper]] [[Auto-stripper]]
/home/mediumgg/public_html/data/attic/start.1754774548.txt.gz · Last modified: by admin
Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki